EMLID products & accessories
Find all the EMLID accessories to make your measurement easier.
All products are compatible with the Reach RS+ and Reach RS2 receiver models.
Survey Pole with a smartphone mount
The three-section construction delivers reliable stability with the help of solid flip locks. It comes equipped with a smartphone mount that fits most control devices and a carrying bag.
0,74 – 1,8m
RTK GNSS modules for UAV mapping
Les 3 sections offrent une stabilité fiable grâce à de solides verrous à bascule.
Equipé d'un support pour smartphone qui s'adapte à la plupart des appareils de contrôle
+ Sac de transport.
Reach M2 and M+ work seamlessly with other Reach receivers over any link and are compatible with any other receiver that supports RTCM3 and NTRIP
Fast Charge Kit
Charges RS2 in 3,5 hours
Compatible with any USB Type-C device
Output power: 18W
Smart integrated protection for devices
Cable length: 1 m
Weight: 70 g
US or EU plugs
To easily hang your phone when taking measurements.
Designed in carbon, this 1.37m rod can extend up to 2.45m and is equipped with a spirit level.
Linux Autopilot Board
Autopilot HAT for Raspberry Pi powered by ArduPilot and ROS
– Connector for RPi
– 4x spacers
– 8x M2.5 screws
Optimal stability for your measurement
It has 3 levels allowing a height of 1.07 to 1.88 meters.
Note: a tribrach is necessary to fix the station, please consult the recommended products below.
With optical plummet
For fine tuning
Secure your mobile station to a tripod with this tribrach adapter
For tripod or handheld fixing
Length 150 mm. Compatible with Reach RS2.
Reach M2/M+ camera hot shoe adapter
For precise time stamping
Hot shoe adapter for Reach M2 and M+. Wires the flash sync pulse from camera to Reach for precise time stamping of each picture. Necessary for PPK workflow. Designed to work with any camera with hot shoe connector, tested to work with Sony, Canon, and Nikon.
Up to 8 km
300% more range compared with FSK radios at the same power
LoRa Spread Spectrum modulation can work on disctances up to 4 times longer compared with traditional FSK radios at the same power output. LoRa radio is used to connect rover to base when internet-delivered corrections are not available.
Frequency Range : 868-915 MHz
Reach M2/M+ LoRa radio
To receive correction from RS2
LoRa radio allows Reach M2 and M+ to receive corrections from Reach RS2 and RS+.
Frequency: 862-1020 MHz
Output power: 100 mW
Transmission range: up to 8 km
Antenna connector: RP-SMA
Weight: 17gr, 32gr with antenna
Size: 50x29x19.6 mm
– LoRa Radio
– Cable for connection to M2/M+
Reach RS+/RS2 Cable 2m w/o 2nd Connector – CBL101
Reach RS+/RS2 Cable 2m w/o 2nd Connector (90°) – CBL108
Reach RS+/RS2 Cable 2m with DB9 MALE Connector – CBL102
Reach RS+/RS2 Cable 2m with DB MALE Connector (90°) – CBL109
Reach RS+/RS2 Cable 2m with DB9 FEMALE Connector – CBL103
Reach RS+/RS2 Cable 2m with DB FEMALE Connector (90°) – CBL110
Reach M+/M2 SMA Antenna Adapter Cable 0.5m – RFC101
Reach M+/M2 Antenna Extension Cable 2m – RFC102
Reach M+/M2 TNC Antenna Adapter Cable 2m – RFC103
Reach M+ JST-GH 6p-6p Cable for Edge – CBL104
Reach M+ JST-GH to DF13 6p-6p Cable for Pixhawk 1 – CBL105
Reach M+ JST-GH to 6p-6p Cable for Pixhawk 2 – CBL106
Education & Research
6% Special Discount on EMLID Accessories
Test & Rental Available
1 Reach RS2 / 1 reach RS+
Other EMLID Accessories
Looking for another accessory? Consult the complete EMLID catalog by clicking below:
Please contact us for any quote or enquiry, we will get back to you as soon as possible.